Jinan Lide Rubber & Plastic Co.Ltd.
English
Home
Video
video
building layer by layer
wire reinforcement, edge curl
compaction
curing
hydrostatic pressure test 1.5 time
vertical machining center
flexibility of rubber expansion joints with threaded unions
lateral and axial movement test
Products
Single Arch Rubber Expansion Joint
Double Arch Rubber Expansion Joint
Wide Arch Rubber Expansion Joint
Spool Type Rubber Expansion Joint
Threaded Union
Control Units
Rubber Pipe Connector
Standard Flanges
PTFE Lined rubber expansion joints
Other products
Abrasion resistance rubber expansion joints
Technology Supports
Testing Instruments
Elastomer Properties
ELASTOMER PHYSICAL AND CHEMICAL PROPERTIES COMPARISON
Standard Flange Dimensions
Installation and Inspection Instructions
Certifications
News
About Us
Contact Us
FAQs
Home
Featured
Factory For India Made Rubber Expansion Joint - A-7 ~Rubber Pipe Connector – Lide
Details Rubber Pipe is an economical, abrasion-resistant replacement for steel and cast iron pipe, either in straight lengths or where a specified radius is required. B-1 Rubber Pipe may be used in conveying ore, corrosive chemicals, sand,and other abrasive slurries. It is absolutely necessary that rigid metal pipe on both ends of the pipe be properly anchored to eliminate the danger of excessive elongation. If the pipeline is not anchored, control units should be used. Material: EPDM, NBR,NR...
inquiry
detail
2018 China New Design 4 Expansion Joint - A-5 ~Threaded Union – Lide
Details Threaded unions is used When an economical threaded pipe connection is needed, the surface of the union is available both hot-dip galvanizing and electroplating. Both ends provided with a malleable iron union with female thread BS or ANSI. Specifications II Working Pressure Mpa (Kgf/Cm2) 1.6 (16) Test Pressure 2.4Mpa Burst Pressure Mpa (Kgf/Cm2) 4.8 (48) Vacuum Kpa (Kgf/Cm2) 86(660) Materials EPDM/NBR/SBR/NR Diameter Range DN15-DN80 Connection Method THREAD Flan...
inquiry
detail
Best Price for Safetech Rubber Expansion Joint - A-6 ~Control Units – Lide
Details A control unit assembly is a system of two or more control rods placed across an expansion joint from flange to flange to minimize possible damage to the expansion joint caused by excessive motion of the pipeline. The control rod assemblies are set at the maximum allowable expansion and/or contraction of the joint and will absorb the static pressure thrust developed at the expansion joint. When used in this manner, they are an additional safety factor, minimizing possible failure of t...
inquiry
detail
Factory making 2 Inch Rubber Coupling - A-2 ~Double Arch Rubber Expansion Joint – Lide
Details Double-arch products are used where more movement is needed. If the piping pressure is much higher, reinforced bolts should be assembled together with flanges. Reinforcement layer of the bellows by Nylon cords and at both ends by hardened steel wire rings. The floating steel flanges are drilled according to DIN, ANSI, BS, JIS and other standards. Specifications I II III Working Pressure Mpa (Kgf/Cm2) 1Mpa (10) 1.6 (16) 2.5 (25) Test Pressure 1.5Mpa 2.4Mpa 3.75Mpa Burst Pr...
inquiry
detail
Factory wholesale Acs Certified Rubber Joints - A-8 ~Standard Flanges – Lide
Details The elastomers are assembled with the mating flanges, with different standards and different pressures. Sometimes, buyers need us to buy for them, shipped together with rubber joints. Below is the flange standards which we can supply: 1) ANSI B16.5, ASME B16.47 FLANGE Design: welding neck, slip on, blind, socket welding, threaded, lap-joint Pressure: 150#, 300#, 600#,900#,1500#, Wall thickness for welding neck flange: STD, SCH40, SCH80, SCH160. SCHXXS Material: carbon steel...
inquiry
detail
<<
< Previous
304
305
306
307
308
309
Next >
>>
Page 308 / 309